LM2596 Adjustable Step-Down (Buck) Module 3A (24V to 12V/5V/3V)
Wire and cable · 1 option in stock
Hook-up wire and cable for machine wiring — gauge, cores and flexibility. The parameters are listed in order of importance: the one at the top decides the most, and no amount of care further down makes up for getting it wrong.
This page lists 1 option, from ¥2.8.
What this part is
LM2596 buck module, dropping a higher voltage (24 V, say) to a lower one (12 V / 5 V), 3 A maximum. A trimmer on the board sets the output. It is the usual way to power fans, sensors and control boards inside a cabinet.
The parts of this item
Figure 1 — Cable needs three things: cores, gauge, length — connectors are extra; leave them out and you crimp your own
The parameters that matter
Not every number on a part like this is worth the same. These are the ones that decide whether it fits and works, and what to look at for each.
| Parameter | What to check |
|---|---|
| Input | 4.5–40 V. The input must be at least 1.5–2 V above the output — this is a buck, it cannot step up. |
| Output current | Rated 3 A; continuous is more stable under 2 A. 3 A is a peak, and it needs airflow. |
| Efficiency | About 80–92 %. The bigger the drop and the current, the more heat. |
| Switching frequency | 150 kHz. |
How to choose, step by step
- Type — Shielded or unshielded, flexible or solid core.
Reading the part numbers
| Part no. | Configuration |
|---|---|
EG-095 | single configuration |
You can order by part number or by selecting the parameters. The part number is fastest, but it does not always encode every parameter — the selector on this page is the authority.
6 common mistakes
- Undersized wire gets hot. Size by current, not by what fits the terminal.
- Drag chain needs flexible cable. Ordinary wire work-hardens and breaks its strands after a few hundred thousand cycles.
- Keep signal and power apart. Running them in parallel couples noise into the signal and you chase it as a "random" fault.
- Stranded wire needs ferrules in screw terminals. Bare strands creep and the joint loosens.
- Measure before you order. Take the old part off and measure it, or send us a photo with the caliper reading — that beats guessing from a model number every time.
- Everything here is in millimetres. Where a size is imperial, convert it: 1" = 25.4 mm, 1/4" = 6.35 mm, 3/32" = 2.38 mm.
Telling it apart from lookalikes
Against the fixed-output version: fixed has no trimmer, so it cannot be knocked out of adjustment — more reliable. Adjustable is flexible and easy to set wrong. Against an MP1584: smaller and faster (1.5 MHz), but 3 A and less tolerant of overvoltage.
Confirming it is the right part
This page has one configuration, so there is nothing to choose — which makes confirming that it is the right part more important than studying the specification. Three steps is enough:
- Measure the mating dimension — the one place this part touches something else: bore, shaft, thread, tube OD, or hex across flats. It is the number people get wrong, and half a millimetre out means it will not fit.
- Measure the outline and the mounting hole spacing. Two parts that do the same job from two makers often differ by 2–3 mm between holes: it looks like it will fit, and it goes on crooked.
- Send us two photographs: one general view showing the machine and where the part sits, and one close-up with the caliper reading in shot. If the machine has a nameplate, include it — plenty of these parts are specific to one machine, and the model number locates them faster than dimensions do.
When to replace it
You do not replace this until it fails — but "still looks usable" and "still reliable" are two different things. Any one of these and it is time:
- Insulation damaged with copper visible.
- Broken strands at a bend — a meter shows intermittent continuity when you flex it.
Fitting and use
Before wiring
- Confirm voltage and polarity first. Reversed, it is destroyed on the first switch-on — there is no second chance. DC parts especially.
- Wire with the power off, then check continuity and insulation with a meter before you apply power.
- Crimp or tin the wire ends. Twisting bare strands onto a terminal gives a high-resistance joint that heats up.
Mounting
- Leave the heated parts some air. Do not mount them against plastic or against the cable run.
- Parts with a direction (fans, check valves) have an arrow. Reversed, you lose most of the airflow or flow.
- Fasten it properly. Vibration loosens terminals, and loose terminals are the most common electrical failure there is.
First power-up
- First power-up from a current-limited supply, or through a fuse. If something is wrong the damage stays small.
- Run it unloaded first, measure current and temperature, then add load.
- After 30 minutes feel the terminals and the cable. Anything noticeably warm means high contact resistance — re-crimp it.
Three things not to do
- Do not connect or disconnect under power unless it is explicitly rated for hot-plug. The arc damages the terminals.
- Do not run above the rating. It works for a while, then it does not.
- Do not skip the earth or the fuse. You save a few yuan and risk the machine.
Matching parts
- Ferrules, heat shrink and drag chain
Lead time, custom work and shipping
- Stock sizes: dispatched in 1–2 working days, subject to stock
- Custom: non-standard sizes, materials and treatments are possible — send quantity and drawing
- Shipping: from Shenzhen; domestic courier by default, DHL or dedicated line for export
- Volume: quantity pricing available, contact us for a quote
If you cannot find the size you need, or you are not sure which one fits, send us the problem you are solving — what machine it goes on, the dimensions of the part you have, what it has to achieve — and we will match it.