V6 Bowden Hotend Kit
Hotend assemblies · 2 voltages · 30 styles · 52 options in stock
Extruder and hotend assemblies for 3D printers. The parameters are listed in order of importance: the one at the top decides the most, and no amount of care further down makes up for getting it wrong.
This page lists 52 options: Voltage 12V / 24V, Style / variant Remote 0.1mm 1.75mm consumables / Remote 0.1mm 3.0mm consumables / Remote 0.2mm 1.75mm consumables / Remote 0.2mm 3.0mm consumables … 30 total. From ¥14.3.
The parts of this item
Figure 1 — If any link is loose, blocked or not seated, it shows up as a clog or as temperature swings.
What each parameter decides
Every parameter below shows the real range available on this page, and what goes wrong if you pick it wrong. Work through them in this order and you will not go far wrong.
| Parameter | Available here | What it decides | If you get it wrong |
|---|---|---|---|
| Voltage | 12V / 24V | it has to match your supply exactly | the wrong voltage burns it out, or it will not turn at all |
| Style / variant | Remote 0.1mm 1.75mm consumables / Remote 0.1mm 3.0mm consumables / Remote 0.2mm 1.75mm consumables / Remote 0.2mm 3.0mm consumables … 30 total | the structural and shape differences | it will not fit, or it will not do the job your mechanism needs |
How to choose, step by step
- Then the heat break — All-metal breaks take higher temperature (300 °C and up) but conduct heat up into the cold zone and can creep and jam. PTFE-lined breaks feed smoothly and do not jam, but top out around 240 °C.
- Then heater block and cartridge — 12V / 24V must match the board (12 V or 24 V); Power sets how fast it comes up to temperature.
How the options on this page are distributed
Figure 2 — how the 52 options on this page are spread across each parameter: the bars on the left show how many options sit in each band, the panel on the right shows the real range of every parameter and how many steps it has.
Variant quick reference
| Voltage | Style / variant | Options |
|---|---|---|
| 12V | Remote 0.1mm 1.75mm consumables / Remote 0.1mm 3.0mm consumables / Remote 0.2mm 1.75mm consumables / Remote 0.2mm 3.0mm consumables … 30 total | 30 |
| 24V | Remote 0.1mm 1.75mm consumables / Remote 0.1mm 3.0mm consumables / Remote 0.2mm 1.75mm consumables / Remote 0.2mm 3.0mm consumables … 22 total | 22 |
This table is a summary: one row per Voltage, with the other parameters available in that group. For an exact combination, use the selector at the top of the page — it shows the single part number and price.
Reading the part numbers
| Part no. | Configuration |
|---|---|
P3-104-12V-JC-1.750.2 | Voltage 12V · Style / variant Short range 1.75mm/0.2mm |
P3-104-12V-JC-1.750.3 | Voltage 12V · Style / variant Short range 1.75mm/0.3mm |
P3-104-12V-JC-1.750.4 | Voltage 12V · Style / variant Short range 1.75mm/0.4mm |
You can order by part number or by selecting the parameters. The part number is fastest, but it does not always encode every parameter — the selector on this page is the authority.
7 common mistakes
- 12 V and 24 V are not interchangeable. A 12 V heater on 24 V dies instantly; 24 V on 12 V never gets hot enough.
- Nozzle threads are M6 or M7. E3D-pattern hotends are mostly M6, some domestic ones are M7 — measure the thread OD before ordering.
- All-metal is not automatically better. If you only print PLA and PETG, a PTFE-lined break is actually less prone to jamming.
- Thermistors differ in B value. The wrong B value puts the reading tens of degrees out, and you either under-extrude or scorch the print.
- Change nozzles hot. Turning one out cold snaps the heat break or opens a leak.
- Measure before you order. Take the old part off and measure it, or send us a photo with the caliper reading — that beats guessing from a model number every time.
- Everything here is in millimetres. Where a size is imperial, convert it: 1" = 25.4 mm, 1/4" = 6.35 mm, 3/32" = 2.38 mm.
When to replace it
You do not replace this until it fails — but "still looks usable" and "still reliable" are two different things. Any one of these and it is time:
- The nozzle orifice has grown (lines come out thick), the flow is off-axis, or it is blocked and will not clear.
- Polymer weeping at the heat break / nozzle joint, with a ring of carbonised plastic around it.
- Heater resistance has drifted and warm-up is slow; the thermistor reading jumps.
Fitting and use
Before wiring
- Confirm voltage and polarity first. Reversed, it is destroyed on the first switch-on — there is no second chance. DC parts especially.
- Wire with the power off, then check continuity and insulation with a meter before you apply power.
- Crimp or tin the wire ends. Twisting bare strands onto a terminal gives a high-resistance joint that heats up.
Mounting
- Leave the heated parts some air. Do not mount them against plastic or against the cable run.
- Parts with a direction (fans, check valves) have an arrow. Reversed, you lose most of the airflow or flow.
- Fasten it properly. Vibration loosens terminals, and loose terminals are the most common electrical failure there is.
First power-up
- First power-up from a current-limited supply, or through a fuse. If something is wrong the damage stays small.
- Run it unloaded first, measure current and temperature, then add load.
- After 30 minutes feel the terminals and the cable. Anything noticeably warm means high contact resistance — re-crimp it.
Three things not to do
- Do not connect or disconnect under power unless it is explicitly rated for hot-plug. The arc damages the terminals.
- Do not run above the rating. It works for a while, then it does not.
- Do not skip the earth or the fuse. You save a few yuan and risk the machine.
Matching parts
- Silicone sock — saves power and holds temperature
- Nozzle cleaning needles — for the occasional blockage
- Spare thermistor and heater cartridge
Lead time, custom work and shipping
- Stock sizes: dispatched in 1–2 working days, subject to stock
- Custom: non-standard sizes, materials and treatments are possible — send quantity and drawing
- Shipping: from Shenzhen; domestic courier by default, DHL or dedicated line for export
- Volume: quantity pricing available, contact us for a quote
If you cannot find the size you need, or you are not sure which one fits, send us the problem you are solving — what machine it goes on, the dimensions of the part you have, what it has to achieve — and we will match it.